The Effects of Irradiation on Uranium-plutonium-fissium Fuel Alloys
The Effects of Irradiation on Uranium-plutonium-fissium Fuel Alloys

Author: J. A. Horak

Publisher:

Published: 1962

Total Pages: 40

ISBN-13:

DOWNLOAD EBOOK

A total of 35 specimens of U-Pu-fissium alloy and 2 specimens of U-10 wt% Pu-5 wt% Mo alloy were irradiated as a part of the fuel-alloy development program for fast breeder reactors at Argonne National Laboratory. Total atom burnups ranged from 1.0 to 1.8% at maximum fuel temperatures ranging from 230 to 470 deg C. Emphasis was placed on the EBR-II Core-III reference fuel material, which is an injection-cast, U-20 wt% Pu-10 wt% fissium alloy. It was found that this material begins to swell catastrophically at irradiation temperatures above 370 deg C. The ability of the fuel to resist swelling did not appear to vary appreciably with minor changes in zirconium or fissium content. Decreasing the Pu to 10 wt%, however, significantly improved the swelling behavior of the alloy. Both pour-cast and thermally cycled material and pour-cast, extruded, and thermally cycled material appeared to be more stable under irradiation than injection-cast material. Under comparable irradiation conditions, the specimens of U-20 wt% Pu- 5 wt% Mo alloy were less dimensionally stable than the U-Pu-fissium alloys investigated.

EFFECTS OF IRRADIATION OF SOME URANIUM-PLUTONIUM ALLOYS. Final Report-- Metallurgy Program 6.5.3 Work Completed
EFFECTS OF IRRADIATION OF SOME URANIUM-PLUTONIUM ALLOYS. Final Report-- Metallurgy Program 6.5.3 Work Completed

Author:

Publisher:

Published: 1958

Total Pages:

ISBN-13:

DOWNLOAD EBOOK

Irradiations were made on a number of uranium-plutonium alloy specimens made from both cast and extruded materials. The cast alloys included alloys of uranium with 3.7, 5.6, and 13.0 wt. % plutonium, and the extruded alloys included alloys of uranium with 9.5, 14.1, and 15.7 wt.% plutonium. One-half of the extruded specimens were given a heat treatment consisting of heating to 545 deg C and cooling to and holding at 500 deg C for one hour in an attempt to remove the preferred orientation that was anticipated from extrusion. The specimens were irradiated to burnups ranging up to 0.54 at. % with central temperatures ranging up to 490 deg C. The cast specimens were all found to have developed severe surface roughening as a result of the irradiation they received, presumably because of excessively large grain sizes present before irradiation. Identically fabricated unalloyed uranium specimens showed similar behavior. The as-extruded alloy specimens maintained good surface smoothness under irradiation, but showed elongations which were dependent on plutonium content. For example, in samples with 0.4 at.% burnup, a 14.1 wt.% plutonium alloy specimen elongated 96%, whereas an 18.7 wt. % plutonium alloy specimen elongated only 5.4%. The heat-treated extruded specimens did not elongate anisotropically, indicating that the heat treatment used was effective in randomizing the grain orientation. However, the heat-treated specimens developed excessive surface roughening, apparently because the heat treatment caused an undesirably large grain size. (auth).

"Pin-cushion" Irradiation of Cast Uranium-plutonium Alloy Specimens

Author: S. H. Paine

Publisher:

Published: 1958

Total Pages: 36

ISBN-13:

DOWNLOAD EBOOK

The irradiation behavior of small pin specimens of chill-cast U-10 wt.% Pu and U-15 wt.% Pu specimens projecting from heat transfer cushions is described. The specimens were coated with a thin layer of carbonyl-deposited nickel. The 15 wt.% Pu pins showed excellent dimensional stability at 1/3 wt.% total burnup. The 10 wt.% Pu specimens were somewhat inferior, failure of one of them indicating that the improvement in performance over unalloyed uranium may be due to the restraint imposed by the cladding.

Irradiation of U-Mo Base Alloys
Irradiation of U-Mo Base Alloys

Author: M. P. Johnson

Publisher:

Published: 1964

Total Pages: 38

ISBN-13:

DOWNLOAD EBOOK

A series of experiments was designed to assess the suitability of uranium-molybdenum alloys as high-temperature, high-burnup fuels for advanced sodium cooled reactors. Specimens with molybdenum contents between 3 and 10% were subjected to capsule irradiation tests in the Materials Testing Reactor, to burnups up to 10,000 Mwd/MTU at temperatures between 800 and 1500 deg F. The results indicated that molybdenum has a considerable effect in reducing the swelling due to irradiation. For example. 3% molybdemum reduces the swelling from 25%, for pure uranium. to 7% at approximates 3,000 Mwd/MTU at 1270 deg F. Further swelling resistance can be gained by increasing the molybdenum content, but the amount gained becomes successively smaller. At higher irradiation levels, the amount of swelling rapidly becomes greater, and larger amounts of molybdenum are required to provide similar resistance. A limit of 7% swelling, at 900 deg F and an irradiation of 7,230 Mwd/ MTU, requires the use of 10% Nonemolybdenum in the alloy. The burnup rates were in the range of 2.0 to 4.0 x 10p13s fissiom/cc-sec. Small ternary additions of silicon and aluminum were shown to have a noticeable effect in reducing swelling when added to a U-3% Mo alloy base. Under the conditions of the present experiment, 0.26% silicon or 0.38% aluminum were equivalent to 1 to 1 1/2% molybdenum. The Advanced Sodium Cooled Reactor requires a fuel capable of being irradiated to 20,000 Mwd/MTU at temperatures up to 1500 deg C in metal fuel, or equivalent in ceramic fuel. It is concluded that even the highest molybdenum contents considered did not produce a fuel capable of operating satisfactorily under these conditions. The alloys would be useful, however, for less exacting conditions. The U-3% Mo alloy is capable of use up to 3,000 Mwd/MTU at temperatures of 1300 deg F before swelling becomes excessive. The addition of silicon and aluminum would increase this limit to at least 3,000 Mwd/MTU, and possibly more if the

THE EFFECTS OF IRRADIATION ON URANIUM-PLUTONIUM-FISSIUM FUEL ALLOYS. Final Report on Metallurgy Program 6.5.5
THE EFFECTS OF IRRADIATION ON URANIUM-PLUTONIUM-FISSIUM FUEL ALLOYS. Final Report on Metallurgy Program 6.5.5

Author:

Publisher:

Published: 1962

Total Pages:

ISBN-13:

DOWNLOAD EBOOK

A total of 35 specimens of U-Pu-fissium alloy and 2 specimens of U-10 wt% Pu-5 wt% Mo alloy were irradiated as a part of the fue1-alloy development program for fast breeder reactors at Argonne National Laboratory. Total atom burnups ranged from 1.0 to 1.8% at maximum fuel temperatures ranging from 230 to 470 deg C. Emphasis was placed on the EBR-II Core-III reference fuel material, which is an injection-cast, U-20 wt% Pu-10 wt% fissium alloy. lt was found that this material begins to swell catastrophically at irradiation temperatures above 370 deg C. The ability of the fuel to resist swelling did not appear to vary appreciably with minor changes in Zr or fissium content. Decreasing the Pu to 10 wt%, however, significantly improved the swelling behavior of the alloy. Both pourcast and thermally cycled material and pour-cast, extruded, and thermally cycled material appeared to be more stable under irradiation than injection-cast material. Under comparable irradiation conditions, the specimens of U-20 wt% Pu- 5 wt% Mo alloy were less dimensionally stable than the U-Pu-fissium alloys investigated. (auth).