This books analyzes different approaches to modeling earthquake-induced structural pounding and shows the results of the studies on collisions between buildings and between bridge segments during ground motions. Aspects related to the mitigation of pounding effects as well as the design of structures prone to pounding are also discussed. Earthquake-induced structural pounding between insufficiently separated buildings, and between bridge segments, has been repeatedly observed during ground motions. The reports after earthquakes indicate that it may result in limited local damage in the case of moderate seismic events, or in considerable destruction or even the collapse of colliding structures during severe ground motions. Pounding in buildings is usually caused by the differences in dynamic properties between structures, which make them vibrate out-of-phase under seismic excitation. In contrast, in the case of longer bridge structures, it is more often the seismic wave propagation effect that induces collisions between superstructure segments during earthquakes.
This book gathers 23 papers by top experts from 11 countries, presented at the 3rd Houston International Forum: Concrete Structures in Earthquake. Designing infrastructures to resist earthquakes has always been the focus and mission of scientists and engineers located in tectonically active regions, especially around the "Pacific Rim of Fire" including China, Japan, and the USA. The pace of research and innovation has accelerated in the past three decades, reflecting the need to mitigate the risk of severe damage to interconnected infrastructures, and to facilitate the incorporation of high-speed computers and the internet. The respective papers focus on the design and analysis of concrete structures subjected to earthquakes, advance the state of knowledge in disaster mitigation, and address the safety of infrastructures in general.
Developments in Earthquake Engineering have focussed on the capacity and response of structures. They often overlook the importance of seismological knowledge to earthquake-proofing of design. It is not enough only to understand the anatomy of the structure, you must also appreciate the nature of the likely earthquake.Seismic design, as detailed in
Throughout the past few years, there has been extensive research done on structural design in terms of optimization methods or problem formulation. But, much of this attention has been on the linear elastic structural behavior, under static loading condition. Such a focus has left researchers scratching their heads as it has led to vulnerable structural configurations. What researchers have left out of the equation is the element of seismic loading. It is essential for researchers to take this into account in order to develop earthquake resistant real-world structures. Structural Seismic Design Optimization and Earthquake Engineering: Formulations and Applications focuses on the research around earthquake engineering, in particular, the field of implementation of optimization algorithms in earthquake engineering problems. Topics discussed within this book include, but are not limited to, simulation issues for the accurate prediction of the seismic response of structures, design optimization procedures, soft computing applications, and other important advancements in seismic analysis and design where optimization algorithms can be implemented. Readers will discover that this book provides relevant theoretical frameworks in order to enhance their learning on earthquake engineering as it deals with the latest research findings and their practical implementations, as well as new formulations and solutions.
Containing the latest research on preparation for and mitigation of future earthquakes, this book addresses an area of increasing importance to many areas around the world. It contains research presented at the ninth and latest in a series of biennial conferences on the topic organised by the Wessex Institute. As world population has concentrated in urban areas, we have seen the consequences of natural disasters take an ever higher toll in human life and property. Adding to this trend, earthquake activity is being registered in areas that were not previously very active, thus the need for research into the application of technological advances to the specific area of earthquake engineering. This volume presents those advances. The papers cover Seismic Isolation and Energy Dissipation; Building Performance During Earthquakes; Nonlinear Numerical Analysis; Performance Based Design; Experimental Studies; Seismic Hazard Evaluation and Microzoning for Structural Design; Seismic Hazard Assessment; Case Studies.
Many important advances in designing earthquake-resistant structures have occurred over the last several years. Civil engineers need an authoritative source of information that reflects the issues that are unique to the field. Comprising chapters selected from the second edition of the best-selling Handbook of Structural Engineering, Earthquake Eng
Despite significant development in earthquake analysis and design in the last 50 years or more, different structures related to industry, infra structure and human habitats get destroyed with monotonic regularity under strong motion earthquake. Even the recent earthquake in Mexico in September 2017 killed a number of people and destroyed national assets amounting to hundreds of millions of dollars. Careful evaluation of the technology reveals that, despite significant development in earthquake engineering, most of the books that are available on the market for reference are primarily focused towards buildings and framed type structures. It is accepted that during an earthquake it is buildings that get destroyed most and has been the biggest killers of human life. Yet, there are a number of structures like retaining walls, water tanks, Bunkers, silos, tall chimneys, bridge piers etc that are equally susceptible to earthquake, and if damaged can cause serious trouble and great economic distress. Unfortunately, many of these systems are analyzed by techniques that are too simplified, unrealistic/obsolete or nothing is done about them, ignoring completely the seismic effects, as no guidelines exist for their analysis/design (like seismic analysis of counterfort retaining walls or dynamic pressures on bunker walls etc.). This highly informative book addresses many of these items for which there exists a significant gap in technology and yet remain an important life line of considerable commercial significance.The book is an outcome of authors' academic research and practice across the four continents (USA, Europe, Africa and Asia) in the last thirty two years, where many of these technologies have been put in practice, that got tested against real time earthquakes. All methods presented herein have been published previously in peer reviewed research journals and international conferences of repute before being put to practice. Professionals working in international EPC and consulting engineering firms, graduates taking advanced courses in earthquake engineering, doctoral scholars pursuing research in earthquake engineering in the area of dynamic soil structure interaction (DSSI) and advanced under graduates wanting to self-learn and update themselves on earthquake analysis and design are greatly benefited from this book.
While numerous books have been written on earthquakes, earthquake resistance design, and seismic analysis and design of structures, none have been tailored for advanced students and practitioners, and those who would like to have most of the important aspects of seismic analysis in one place. With this book, readers will gain proficiencies in the following: fundamentals of seismology that all structural engineers must know; various forms of seismic inputs; different types of seismic analysis like, time and frequency domain analyses, spectral analysis of structures for random ground motion, response spectrum method of analysis; equivalent lateral load analysis as given in earthquake codes; inelastic response analysis and the concept of ductility; ground response analysis and seismic soil structure interaction; seismic reliability analysis of structures; and control of seismic response of structures. Provides comprehensive coverage, from seismology to seismic control Contains useful empirical equations often required in the seismic analysis of structures Outlines explicit steps for seismic analysis of MDOF systems with multi support excitations Works through solved problems to illustrate different concepts Makes use of MATLAB, SAP2000 and ABAQUAS in solving example problems of the book Provides numerous exercise problems to aid understanding of the subject As one of the first books to present such a comprehensive treatment of the topic, Seismic Analysis of Structures is ideal for postgraduates and researchers in Earthquake Engineering, Structural Dynamics, and Geotechnical Earthquake Engineering. Developed for classroom use, the book can also be used for advanced undergraduate students planning for a career or further study in the subject area. The book will also better equip structural engineering consultants and practicing engineers in the use of standard software for seismic analysis of buildings, bridges, dams, and towers. Lecture materials for instructors available at www.wiley.com/go/dattaseismic
