Transient Electro-Thermal Modeling of Bipolar Power Semiconductor Devices
Transient Electro-Thermal Modeling of Bipolar Power Semiconductor Devices

Author: Tanya Kirilova Gachovska

Publisher: Morgan & Claypool Publishers

Published: 2013-11-01

Total Pages: 85

ISBN-13: 1627051902

DOWNLOAD EBOOK

This book presents physics-based electro-thermal models of bipolar power semiconductor devices including their packages, and describes their implementation in MATLAB and Simulink. It is a continuation of our first book Modeling of Bipolar Power Semiconductor Devices. The device electrical models are developed by subdividing the devices into different regions and the operations in each region, along with the interactions at the interfaces, are analyzed using the basic semiconductor physics equations that govern device behavior. The Fourier series solution is used to solve the ambipolar diffusion equation in the lightly doped drift region of the devices. In addition to the external electrical characteristics, internal physical and electrical information, such as junction voltages and carrier distribution in different regions of the device, can be obtained using the models. The instantaneous dissipated power, calculated using the electrical device models, serves as input to the thermal model (RC network with constant and nonconstant thermal resistance and thermal heat capacity, or Fourier thermal model) of the entire module or package, which computes the junction temperature of the device. Once an updated junction temperature is calculated, the temperature-dependent semiconductor material parameters are re-calculated and used with the device electrical model in the next time-step of the simulation. The physics-based electro-thermal models can be used for optimizing device and package design and also for validating extracted parameters of the devices. The thermal model can be used alone for monitoring the junction temperature of a power semiconductor device, and the resulting simulation results used as an indicator of the health and reliability of the semiconductor power device.

Transient Electro-Thermal Modeling on Power Semiconductor Devices
Transient Electro-Thermal Modeling on Power Semiconductor Devices

Author: Tanya Kirilova Gachovska

Publisher: Springer Nature

Published: 2022-06-01

Total Pages: 68

ISBN-13: 3031025067

DOWNLOAD EBOOK

This book presents physics-based electro-thermal models of bipolar power semiconductor devices including their packages, and describes their implementation in MATLAB and Simulink. It is a continuation of our first book Modeling of Bipolar Power Semiconductor Devices. The device electrical models are developed by subdividing the devices into different regions and the operations in each region, along with the interactions at the interfaces, are analyzed using the basic semiconductor physics equations that govern device behavior. The Fourier series solution is used to solve the ambipolar diffusion equation in the lightly doped drift region of the devices. In addition to the external electrical characteristics, internal physical and electrical information, such as junction voltages and carrier distribution in different regions of the device, can be obtained using the models. The instantaneous dissipated power, calculated using the electrical device models, serves as input to the thermal model (RC network with constant and nonconstant thermal resistance and thermal heat capacity, or Fourier thermal model) of the entire module or package, which computes the junction temperature of the device. Once an updated junction temperature is calculated, the temperature-dependent semiconductor material parameters are re-calculated and used with the device electrical model in the next time-step of the simulation. The physics-based electro-thermal models can be used for optimizing device and package design and also for validating extracted parameters of the devices. The thermal model can be used alone for monitoring the junction temperature of a power semiconductor device, and the resulting simulation results used as an indicator of the health and reliability of the semiconductor power device.

Modeling Bipolar Power Semiconductor Devices
Modeling Bipolar Power Semiconductor Devices

Author: Tanya K. Gachovska

Publisher: Morgan & Claypool Publishers

Published: 2013-03

Total Pages: 96

ISBN-13: 162705121X

DOWNLOAD EBOOK

This book presents physics-based models of bipolar power semiconductor devices and their implementation in MATLAB and Simulink. The devices are subdivided into different regions, and the operation in each region, along with the interactions at the interfaces which are analyzed using basic semiconductor physics equations that govern their behavior. The Fourier series solution is used to solve the ambipolar diffusion equation in the lightly doped drift region of the devices. In addition to the external electrical characteristics, internal physical and electrical information, such as the junction voltages and the carrier distribution in different regions of the device, can be obtained using the models.

Modeling Bipolar Power Semiconductor Devices
Modeling Bipolar Power Semiconductor Devices

Author: Tanya K. Gachovska

Publisher: Springer Nature

Published: 2022-05-31

Total Pages: 88

ISBN-13: 3031024982

DOWNLOAD EBOOK

This book presents physics-based models of bipolar power semiconductor devices and their implementation in MATLAB and Simulink. The devices are subdivided into different regions, and the operation in each region, along with the interactions at the interfaces which are analyzed using basic semiconductor physics equations that govern their behavior. The Fourier series solution is used to solve the ambipolar diffusion equation in the lightly doped drift region of the devices. In addition to the external electrical characteristics, internal physical and electrical information, such as the junction voltages and the carrier distribution in different regions of the device, can be obtained using the models.

Digital Control in Power Electronics
Digital Control in Power Electronics

Author: Simone Buso

Publisher: Morgan & Claypool Publishers

Published: 2015-05-01

Total Pages: 231

ISBN-13: 1627057544

DOWNLOAD EBOOK

This book presents the reader, whether an electrical engineering student in power electronics or a design engineer, a selection of power converter control problems and their basic digital solutions, based on the most widespread digital control techniques. The presentation is primarily focused on different applications of the same power converter topology, the half-bridge voltage source inverter, considered both in its single- and three-phase implementation. This is chosen as the test case because, besides being simple and well known, it allows the discussion of a significant spectrum of the most frequently encountered digital control applications in power electronics, from digital pulse width modulation (DPWM) and space vector modulation (SVM), to inverter output current and voltage control, ending with the relatively more complex VSI applications related to the so called smart-grid scenario. This book aims to serve two purposes: (1) to give a basic, introductory knowledge of the digital control techniques applied to power converters; and (2) to raise the interest for discrete time control theory, stimulating new developments in its application to switching power converters.

Power Electronics for Photovoltaic Power Systems
Power Electronics for Photovoltaic Power Systems

Author: Mahinda Vilathgamuwa

Publisher: Morgan & Claypool Publishers

Published: 2015-08-01

Total Pages: 133

ISBN-13: 1627057765

DOWNLOAD EBOOK

The world energy demand has been increasing in a rapid manner with the increase of population and rising standard of living. The world population has nearly doubled in the last 40 years from 3.7 billion people to the present 7 billion people. It is anticipated that world population will grow towards 8 billion around 2030. Furthermore, the conventional fossil fuel supplies become unsustainable as the energy demand in emerging big economies such as China and India would rise tremendously where the China will increase its energy demand by 75% and India by 100% in the next 25 years. With dwindling natural resources, many countries throughout the world have increasingly invested in renewable resources such as photovoltaics (PV) and wind. The world has seen immense growth in global photovoltaic power generation over the last few decades. For example, in Australia, renewable resources represented nearly 15% of total power generation in 2013. Among renewable resources, solar and wind account for 38% of generation. In near future, energy in the domestic and industrial sector will become ""ubiquitous"" where consumers would have multiple sources to get their energy. Another such prediction is that co-location of solar and electrical storage will see a rapid growth in global domestic and industrial sectors; conventional power companies, which dominate the electricity market, will face increasing challenges in maintaining their incumbent business models. The efficiency, reliability and cost-effectiveness of the power converters used to interface PV panels to the mains grid and other types of off-grid loads are of major concern in the process of system design. This book describes state-of-the-art power electronic converter topologies used in various PV power conversion schemes. This book aims to provide a reader with a wide variety of topologies applied in different circumstances so that the reader would be able to make an educated choice for a given application.

Computer Techniques for Dynamic Modeling of DC-DC Power Converters
Computer Techniques for Dynamic Modeling of DC-DC Power Converters

Author: Farzin Asadi

Publisher: Springer Nature

Published: 2022-06-01

Total Pages: 75

ISBN-13: 3031025040

DOWNLOAD EBOOK

Computers play an important role in the analyzing and designing of modern DC-DC power converters. This book shows how the widely used analysis techniques of averaging and linearization can be applied to DC-DC converters with the aid of computers. Obtained dynamical equations may then be used for control design. The book is composed of two chapters. Chapter 1 focuses on the extraction of control-to-output transfer function. A second-order converter (a buck converter) and a fourth-order converter (a Zeta converter) are studied as illustrative examples in this chapter. Both ready-to-use software packages, such as PLECS® and MATLAB® programming, are used throught this chapter. The input/output characteristics of DC-DC converters are the object of considerations in Chapter 2. Calculation of input/output impedance is done with the aid of MATLAB® programming in this chapter. The buck, buck-boost, and boost converter are the most popular types of DC-DC converters and used as illustrative examples in this chapter. This book can be a good reference for researchers involved in DC-DC converters dynamics and control.

Dynamics and Control of DC-DC Converters
Dynamics and Control of DC-DC Converters

Author: Farzin Asadi

Publisher: Springer Nature

Published: 2022-05-31

Total Pages: 229

ISBN-13: 3031025024

DOWNLOAD EBOOK

DC-DC converters have many applications in the modern world. They provide the required power to the communication backbones, they are used in digital devices like laptops and cell phones, and they have widespread applications in electric cars, to just name a few. DC-DC converters require negative feedback to provide a suitable output voltage or current for the load. Obtaining a stable output voltage or current in presence of disturbances such as: input voltage changes and/or output load changes seems impossible without some form of control. This book tries to train the art of controller design for DC-DC converters. Chapter 1 introduces the DC-DC converters briefly. It is assumed that the reader has the basic knowledge of DC-DC converter (i.e., a basic course in power electronics). The reader learns the disadvantages of open loop control in Chapter 2. Simulation of DC-DC converters with the aid of Simulink® is discussed in this chapter as well. Extracting the dynamic models of DC-DC converters is studied in Chapter 3. We show how MATLAB® and a software named KUCA can be used to do the cumbersome and error-prone process of modeling automatically. Obtaining the transfer functions using PSIM® is studied as well. These days, softwares are an integral part of engineering sciences. Control engineering is not an exception by any means. Keeping this in mind, we design the controllers using MATLAB® in Chapter 4. Finally, references are provided at the end of each chapter to suggest more information for an interested reader. The intended audiencies for this book are practice engineers and academians.