The steel storage rack as described can be successfully used in storage of irregular and small lot items which can be placed on pallets without overlap. Saving of cube can thus be obtained with items that otherwise do not lend themselves to tiering. Steel construction has the advantage over wood in that it is permanent and not subject to deterioration over a period of time. Structural strength is also not dependent on the condition of the wood at time of fabrication.
During the past few decades, the number of large public warehouse stores (often referred to as big-box stores) across the nation has grown significantly, changing both consumer buying habits and the public's risk of injury during earthquakes. During an earthquake, occupant safety in a big-box store depends on both the structural performance of the building and on the performance of the storage racks and their contents. Earthquake ground motions can cause storage racks to collapse or overturn if they are not properly designed, installed, maintained, and loaded. In addition, goods stored on the racks may spill or topple off. Both occurrences pose a life-safety risk to the exposed shopping public. The immediate stimulus for the project that resulted in this report was a 2003 request from the State of Washington to the Federal Emergency Management Agency (FEMA) for guidance concerning the life-safety risk posed by the storage racks in publicly accessible areas of retail stores, especially the risk of rack collapse of loss of stored goods during an earthquake. FEMA asked the Building Seismic Safety Council (BSSC) to develop the requested guidance. To do so, the BSSC established a Rack Project Task Group composed of practicing engineers, storage rack designers, researchers, representatives of the Rack Manufacturers Institute (RMI) and the Retail Industry Leaders Association, and members of applicable technical subcommittees responsible for updating the NEHRP Recommended Provisions. In developing this guidance document, the Task Group focused primarily on steel single selective pallet storage racks. It reviewed available information on storage rack performance during earthquakes and the background on the development of standards and code requirements for storage racks; assessed seismic requirements for storage racks and current practices with respect to rack design, maintenance and operations, quality assurance, and post-earthquake inspections; and examined available research and testing data. Based on its study, the Task Group developed short-term recommendations to improve current practice and formulated long-term recommendations to serve as the basis for improved standards documents such as the NEHRP Recommended Provisions, ASCE 7, and the RMI-developed storage rack specification. Over the near term, the Task Group recommends that the 2003 NEHRP Recommended Provisions requirements for steel single selective pallet storage rack design be followed and that connections be checked in accordance with a procedure to be developed by RMI. The Task Group also recommends that additional guidance presented in this report be voluntarily adopted by store owners and operators. Further, given the fact that maintenance and use of storage racks is a key element to their acceptable performance during earthquakes, store owners and operators should adopt an appropriate quality assurance plan; as a minimum, the best self-imposed practices of store owners and operators should be maintained. The Task Group's primary long-term recommendation is that the RMI specification be brought into conformance with the 2003 NEHRP Recommended Provisions, which is the basis for seismic requirements found in current seismic design standards and model building codes. The Task Group also recommends that optional performance-based and limit state procedures and component cyclic testing procedures be incorporated into the RMI-developed specification. Compliance with these procedures will demonstrate that the storage racks have the capacity to resist maximum considered earthquake ground motions without collapse. It also is recommended that regulatory bodies periodically review the quality assurance programs of stores and implement any regulations needed to satisfy life-safety concerns that relate to the securing of rack contents and rack maintenance and use.
Special edition includes both Canadian standards for: User guide for steel storage racks (pages 1-18) and Standard for the design and construction of steel storage racks (pages 19-35).
This book presents the main outcomes of the first European research project on the seismic behavior of adjustable steel storage pallet racking systems. In particular, it describes a comprehensive and unique set of full-scale tests designed to assess such behavior. The tests performed include cyclic tests of full-scale rack components, namely beam-to-upright connections and column base connections; static and dynamic tests to assess the friction factor between pallets and rack beams; full-scale pushover and pseudodynamic tests of storage racks in down-aisle and cross-aisle directions; and full-scale dynamic tests on two-bay, three-level rack models. The implications of the findings of this extensive testing regime on the seismic behavior of racking systems are discussed in detail, highlighting e.g. the confirmation that under severe dynamic conditions “sliding” is the main factor influencing rack response. This work was conceived during the development of the SEISRACKS project. Its outcomes will contribute significantly to increasing our knowledge of the structural behavior of racks under earthquake conditions and should inform future rack design.
