CREEP, SHRINKAGE AND DURABILITY MECHANICS OF CONCRETE AND CONCRETE STRUCTURES contains the keynote lectures, technical reports and contributed papers presented at the Eighth International Conference on Creep, Shrinkage and Durability of Concrete and Concrete Structures (CONCREEP8, Ise-shima, Japan, 30 September - 2 October 2008). The topics covered
This comprehensive treatise covers in detail practical methods of analysis as well as advanced mathematical models for structures highly sensitive to creep and shrinkage. Effective computational algorithms for century-long creep effects in structures, moisture diffusion and high temperature effects are presented. The main design codes and recommendations (including RILEM B3 and B4) are critically compared. Statistical uncertainty of century-long predictions is analyzed and its reduction by extrapolation is discussed, with emphasis on updating based on short-time tests and on long-term measurements on existing structures. Testing methods and the statistics of large randomly collected databases are critically appraised and improvements of predictions of multi-decade relaxation of prestressing steel, cyclic creep in bridges, cracking damage, etc., are demonstrated. Important research directions, such as nanomechanical and probabilistic modeling, are identified, and the need for separating the long-lasting autogenous shrinkage of modern concretes from the creep and drying shrinkage data and introducing it into practical prediction models is emphasized. All the results are derived mathematically and justified as much as possible by extensive test data. The theoretical background in linear viscoelasticity with aging is covered in detail. The didactic style makes the book suitable as a textbook. Everything is properly explained, step by step, with a wealth of application examples as well as simple illustrations of the basic phenomena which could alternate as homeworks or exams. The book is of interest to practicing engineers, researchers, educators and graduate students.
From July 10th through July 13th, 1994, an informal workshop co-organized by RILEM committees 116-PCD and 123-MME was held at Saint-Remy-Ies Chevreuse, France, and attended by 38 delegates from 16 countries. Twenty-nine papers were presented, converging the general subjects of modelling micro structures and predicting durability of concrete and other cement-based materials. A short summary follows: G. M. Idom's paper entitled "Modelling Research for Concrete Engineering" serves as an introduction to the workshop, presenting an overview of modelling research with the conelusion that the broad practica1 objective is to produce high-quality concrete. This means that many characteristics, ranging from rheology to alkali-silica reaction, must be modelled. In other words, the system must be understood. Idom's paper sets the stage for papers in two general areas: 1) models and 2) transport properties. After this, abrief survey of the develop ment of microstructurally-based models is presented. A elose relationship between computer power and speed is suggested. The first group of papers on models covers the subjects of scale and resolution. Most models define and predict characteristics of the pore system, which range in scale from nanometer to millimeter. Various types ofnetworks are proposed in these papers. A good microstructural model must describe the pores and other phases at ascale appropriate to the properties that the model predicts. Also, a good model should be based on fundamental knowledge. In the case of cement-based materials, the important properties may depend on the microstructure, especially the porosity, at several scales.
The book presents the underlying theories of the different approaches for modeling cracking of concrete and provides a critical survey of the state-of-the-art in computational concrete mechanics. It covers a broad spectrum of topics related to modeling of cracks, including continuum-based and discrete crack models, meso-scale models, advanced discretization strategies to capture evolving cracks based on the concept of finite elements with embedded discontinuities and on the extended finite element method, and extensions to coupled problems such a hygro-mechanical problems as required in computational durability analyses of concrete structures.
The second edition of the Structural Concrete Textbook is an extensive revision that reflects advances in knowledge and technology over the past decade. It was prepared in the intermediate period from the CEP-FIP Model Code 1990 (MC90) tofib Model Code 2010 (MC2010), and as such incorporates a significant amount of information that has been already finalized for MC2010, while keeping some material from MC90 that was not yet modified considerably. The objective of the Textbook is to give detailed information on a wide range of concrete engineering from selection of appropriate structural system and also materials, through design and execution and finally behaviour in use. The revised fib Structural Concrete Textbook covers the following main topics: phases of design process, conceptual design, short and long term properties of conventional concrete (including creep, shrinkage, fatigue and temperature influences), special types of concretes (such as self compacting concrete, architectural concrete, fibre reinforced concrete, high and ultra high performance concrete), properties of reinforcing and prestressing materials, bond, tension stiffening, moment-curvature, confining effect, dowel action, aggregate interlock; structural analysis (with or without time dependent effects), definition of limit states, control of cracking and deformations, design for moment, shear or torsion, buckling, fatigue, anchorages, splices, detailing; design for durability (including service life design aspects, deterioration mechanisms, modelling of deterioration mechanisms, environmental influences, influences of design and execution on durability); fire design (including changes in material and structural properties, spalling, degree of deterioration), member design (linear members and slabs with reinforcement layout, deep beams); management, assessment, maintenance, repair (including, conservation strategies, risk management, types of interventions) as well as aspects of execution (quality assurance), formwork and curing. The updated Textbook provides the basics of material and structural behaviour and the fundamental knowledge needed for the design, assessment or retrofitting of concrete structures. It will be essential reading material for graduate students in the field of structural concrete, and also assist designers and consultants in understanding the background to the rules they apply in their practice. Furthermore, it should prove particularly valuable to users of the new editions of Eurocode 2 for concrete buildings, bridges and container structures, which are based only partly on MC90 and partly on more recent knowledge which was not included in the 1999 edition of the Textbook.
Presents the proceedings of the 5th RILEM International Symposium, held in Barcelona in September 1993. The papers discuss creep and shrinkage of concrete, and should be of interest to cement and concrete technologists and researchers, as well as structural engineers.
This conference proceedings brings together the work of researchers and practising engineers concerned with computational modelling of complex concrete, reinforced concrete and prestressed concrete structures in engineering practice. The subjects considered include computational mechanics of concrete and other cementitious materials, including masonry. Advanced discretisation methods and microstructural aspects within multi-field and multi-scale settings are discussed, as well as modelling formulations and constitutive modelling frameworks and novel experimental programmes. The conference also considered the need for reliable, high-quality analysis and design of concrete structures in regard to safety-critical structures, with a view to adopting these in codes of practice or recommendations. The book is of special interest to researchers in computational mechanics, and industry experts in complex nonlinear simulations of concrete structures.
Hat ein Werkstoff seine Elastizitatsgrenze erreicht, so verhalt er sich inelastisch. Ingenieure und Designer mussen wissen, mit welchen Eigenschaften dann zu rechnen ist. Dieser Band vermittelt Ihnen den aktuellen Wissensstand auf dem Gebiet des plastischen Verhaltens und der plastischen Zug-Spannungs-Beziehungen. Behandelt werden in erster Linie Baustoffe, vor allem Stahl, aber auch Beton und Boden. Eine ausgewogene Mischung aus qualitativer Diskussion und mathematischer Theorie! (05/00)
