Nondestructive Testing Technique to Quantify Deterioration from Marine Borer Attack in Sitka Spruce and Western Hemlock Logs
Nondestructive Testing Technique to Quantify Deterioration from Marine Borer Attack in Sitka Spruce and Western Hemlock Logs

Author: Robert Jon Ross

Publisher:

Published: 2014

Total Pages: 8

ISBN-13:

DOWNLOAD EBOOK

Stress-wave nondestructive evaluation (NDE) techniques are used widely in the forest products industry--from the grading of wood veneer to inspection of timber structures. Inspection professionals frequently use stress-wave NDE techniques to locate internal voids and decayed or deteriorated areas in large timbers. Although these techniques have proven useful, little information exists concerning the relationship between stress-wave parameters and deterioration observed as a consequence of marine borer attack. In this pilot test, we examined the relationship between stress-wave transmission time and the quality of wood in Sitka spruce and western hemlock logs that had varying degrees of deterioration as a consequence of attack from marine borers. Stress-wave transmission time, perpendicular to grain, was measured at several locations on each log. The logs were then sawn into lumber, which was then visually evaluated. A relationship was observed between stress-wave transmission time and deterioration of the logs and the yield of lumber from the logs.

Wood Properties and Processing
Wood Properties and Processing

Author: Miha Humar

Publisher: MDPI

Published: 2020-05-23

Total Pages: 350

ISBN-13: 3039288210

DOWNLOAD EBOOK

Wood-based materials are CO2-neutral, renewable, and considered to be environmentally friendly. The huge variety of wood species and wood-based composites allows a wide scope of creative and esthetic alternatives to materials with higher environmental impacts during production, use and disposal. Quality of wood is influenced by the genetic and environmental factors. One of the emerging uses of wood are building and construction applications. Modern building and construction practices would not be possible without use of wood or wood-based composites. The use of composites enables using wood of lower quality for the production of materials with engineered properties for specific target applications. Even more, the utilization of such reinforcing particles as carbon nanotubes and nanocellulose enables development of a new generation of composites with even better properties. The positive aspect of decomposability of waste wood can turn into the opposite when wood or wood-based materials are exposed to weathering, moisture oscillations, different discolorations, and degrading organisms. Protective measures are therefore unavoidable for many outdoor applications. Resistance of wood against different aging factors is always a combined effect of toxic or inhibiting ingredients on the one hand, and of structural, anatomical, or chemical ways of excluding moisture on the other.

Nondestructive Characterization of Materials IV
Nondestructive Characterization of Materials IV

Author: J.F. Bussière

Publisher: Springer Science & Business Media

Published: 1992-02-29

Total Pages: 536

ISBN-13: 9780306440472

DOWNLOAD EBOOK

There is a great deal of interest in extending nondestructive technologies beyond the location and identification of cracks and voids. Specifically there is growing interest in the application of nondestructive evaluation (NOEl to the measurement of physical and mechanical properties of materials. The measurement of materials properties is often referred to as materials characterization; thus nondestructive techniques applied to characterization become nondestructive characterization (NDCl. There are a number of meetings, proceedings and journals focused upon nondestructive technologies and the detection and identification of cracks and voids. However, the series of symposia, of which these proceedings represent the fourth, are the only meetings uniquely focused upon nondestructive characterization. Moreover, these symposia are especially concerned with stimulating communication between the materials, mechanical and manufacturing engineer and the NDE technology oriented engineer and scientist. These symposia recognize that it is the welding of these areas of expertise that is necessary for practical development and application of NDC technology to measurements of components for in service life time and sensor technology for intelligent processing of materials. These proceedings are from the fourth international symposia and are edited by c.o. Ruud, J. F. Bussiere and R.E. Green, Jr. . The dates, places, etc of the symposia held to date area as follows: Symposia on Nondestructive Methods for TITLE: Material Property Determination DATES: April 6-8, 1983 PLACE: Hershey, PA, USA CHAIRPERSONS: C.O. Ruud and R.E. Green, Jr.