Computers play an important role in the analyzing and designing of modern DC-DC power converters. This book shows how the widely used analysis techniques of averaging and linearization can be applied to DC-DC converters with the aid of computers. Obtained dynamical equations may then be used for control design. The book is composed of two chapters. Chapter 1 focuses on the extraction of control-to-output transfer function. A second-order converter (a buck converter) and a fourth-order converter (a Zeta converter) are studied as illustrative examples in this chapter. Both ready-to-use software packages, such as PLECS® and MATLAB® programming, are used throught this chapter. The input/output characteristics of DC-DC converters are the object of considerations in Chapter 2. Calculation of input/output impedance is done with the aid of MATLAB® programming in this chapter. The buck, buck-boost, and boost converter are the most popular types of DC-DC converters and used as illustrative examples in this chapter. This book can be a good reference for researchers involved in DC-DC converters dynamics and control.
The most critical part of the modern switching-mode power supply is the regulated dc/dc converter. Its dynamic behavior directly determines or influences four of the important characteristics of the power supply: • Stability of the feedback loop • Rejection of input-voltage ripple and the closely-related transient re sponse to input-voltage perturbation • Output impedance and the closely-related transient response to load perturbation • Compatibility with the input EMI filter Due to the complexity of the operation of the converter, predicting its dynamic behavior has not been easy. Without accurate prediction, and depending only on building the circuit and tinkering with it until the operation is satisfactory, the engineering cost can easily escalate and schedules can be missed. The situation is not much better when the circuit is built in the computer, using a general-purpose circuit-simulation program such as SPICE. (At the end of this book is a form for obtaining information on a computer program especially well suited for dynamic analysis of switching-mode power converters: DYANA, an acronym for "DYnamic ANAlysis. " DYANA is based on the method given in this book. ) The main goal of this book is to help the power-supply designer in the prediction of the dynamic behavior by providing user-friendly analytical tools, concrete results of already-made analyses, tabulated for easy application by the reader, and examples of how to apply the tools provided in the book.
DC-DC converters have many applications in the modern world. They provide the required power to the communication backbones, they are used in digital devices like laptops and cell phones, and they have widespread applications in electric cars, to just name a few. DC-DC converters require negative feedback to provide a suitable output voltage or current for the load. Obtaining a stable output voltage or current in presence of disturbances such as: input voltage changes and/or output load changes seems impossible without some form of control. This book tries to train the art of controller design for DC-DC converters. Chapter 1 introduces the DC-DC converters briefly. It is assumed that the reader has the basic knowledge of DC-DC converter (i.e., a basic course in power electronics). The reader learns the disadvantages of open loop control in Chapter 2. Simulation of DC-DC converters with the aid of Simulink® is discussed in this chapter as well. Extracting the dynamic models of DC-DC converters is studied in Chapter 3. We show how MATLAB® and a software named KUCA can be used to do the cumbersome and error-prone process of modeling automatically. Obtaining the transfer functions using PSIM® is studied as well. These days, softwares are an integral part of engineering sciences. Control engineering is not an exception by any means. Keeping this in mind, we design the controllers using MATLAB® in Chapter 4. Finally, references are provided at the end of each chapter to suggest more information for an interested reader. The intended audiencies for this book are practice engineers and academians.
AVERAGE CURRENT-MODE CONTROL OF DC-DC POWER CONVERTERS An authoritative one-stop guide to the analysis, design, development, and control of a variety of power converter systems Average Current-Mode Control of DC-DC Power Converters provides comprehensive and up-to-date information about average current-mode control (ACMC) of pulse-width modulated (PWM) dc-dc converters. This invaluable one-stop resource covers both fundamental and state-of-the-art techniques in average current-mode control of power electronic converters???featuring novel small-signal models of non-isolated and isolated converter topologies with joint and disjoint switching elements and coverage of frequency and time domain analysis of controlled circuits. The authors employ a systematic theoretical framework supported by step-by-step derivations, design procedures for measuring transfer functions, challenging end-of-chapter problems, easy-to-follow diagrams and illustrations, numerous examples for different power supply specifications, and practical tips for developing power-stage small-signal models using circuit-averaging techniques. The text addresses all essential aspects of modeling, design, analysis, and simulation of average current-mode control of power converter topologies, such as buck, boost, buck-boost, and flyback converters in operating continuous-conduction mode (CCM). Bridging the gap between fundamental modeling methods and their application in a variety of switched-mode power supplies, this book: Discusses the development of small-signal models and transfer functions related to the inner current and outer voltage loops Analyzes inner current loops with average current-mode control and describes their dynamic characteristics Presents dynamic properties of the poles and zeros, time-domain responses of the control circuits, and comparison of relevant modeling techniques Contains a detailed chapter on the analysis and design of control circuits in time-domain and frequency-domain Provides techniques required to produce professional MATLAB plots and schematics for circuit simulations, including example MATLAB codes for the complete design of PWM buck, boost, buck-boost, and flyback DC-DC converters Includes appendices with design equations for steady-state operation in CCM for power converters, parameters of commonly used power MOSFETs and diodes, SPICE models of selected MOSFETs and diodes, simulation tools including introductions to SPICE, MATLAB, and SABER, and MATLAB codes for transfer functions and transient responses Average Current-Mode Control of DC-DC Power Converters is a must-have reference and guide for researchers, advanced graduate students, and instructors in the area of power electronics, and for practicing engineers and scientists specializing in advanced circuit modeling methods for various converters at different operating conditions.
Energy efficient, wide-bandwidth, and well-regulated dc-dc power converters are in great demand in today's emerging technologies in areas such as medical, communication, aerospace, and automotive industries. In addition to design and selection of the converter components, a robust closed-loop modeling is very essential for reliable power-electronic systems.Two closed-loop control techniques for power converters exist: voltage-mode control and current-mode control. The principles of voltage-mode control have been explored in great depths by researchers over the last two decades. However, the dynamic modeling of current-mode controlled dc-dc power converters has many uncharted areas that needs careful attention. Two main methods exist under the category of current-mode control: peak current-mode control and average current-mode control. Both of these control strategies are very attractive in applications that require fast control speeds, improved voltage regulation, and improved power supply noise rejection ratio. In recent technological advancements, where high noise immunity and tight regulation are desired, the average current-mode control has proven to be a superior choice, when compared to other control techniques for power converters. In this dissertation, a complete systematic theoretical framework for analysis, design, characterization, and measurements of the dc-dc converters with average current-mode control is introduced. To overcome the drawbacks of the traditional average current-mode control method, a new, true-averaged current-mode control technique is proposed. The new technique is implemented on the basic converter topologies namely, buck, boost, and buck-boost. The dynamic small-signal models of the converter power-stages are developed using the circuit-averaging technique. Theinner-current loop of the power converters is designed and their frequency-domain, time-domain, and pole-zero domain characteristics are exploited. Subsequently, the outer-voltage loop is designed in the presence of current-controlled power stage and the overall converter performance is evaluated against dynamically-varying operating conditions.A laboratory prototype of a buck-boost converter for 12 V to 5 V at 25 W operating at 200 kHz was designed, built, and measured. The theoretically predicted results were validated both through simulations and experiments. The techniques to measure the small-signal open-loop and closed-loop transfer functions are also provided. Excellent agreement between the theoretical and experimental results were observed.
Modeling is the process of formulating a mathematical description of the system. A model, no matter how detailed, is never a completely accurate representation of a real physical system. A mathematical model is always just an approximation of the true, physical reality of the system dynamics. Uncertainty refers to the differences or errors between model and real systems and whatever methodology is used to present these errors will be called an uncertainty model. Successful robust control-system design would depend on, to a certain extent, an appropriate description of the perturbation considered. Modeling the uncertainties in the switch mode DC-DC converters is an important step in designing robust controllers. This book studies different techniques which can be used to extract the uncertain model of DC-DC converters. Once the uncertain model is extracted, robust control techniques such as ∞ and μ synthesis can be used to design the robust controller. The book composed of two case studies. The first one is a buck converter and the second one is a Zeta converter. MATLAB® programming is used extensively throughout the book. Some sections use PLECS® as well. This book is intended to be guide for both academicians and practicing engineers.
Power electronics systems are nonlinear variable structure systems. They involve passive components such as resistors, capacitors, and inductors, semiconductor switches such as thyristors and MOSFETs, and circuits for control. The analysis and design of such systems presents significant challenges. Fortunately, increased availability of powerful computer and simulation programs makes the analysis/design process much easier. PSIM® is an electronic circuit simulation software package, designed specifically for use in power electronics and motor drive simulations but can be used to simulate any electronic circuit. With fast simulation speed and user friendly interface, PSIM provides a powerful simulation environment to meed the user simulation and development needs. This book shows how to simulate the power electronics circuits in PSIM environment. The prerequisite for this book is a first course on power electronics. This book is composed of eight chapters: Chapter 1 is an introduction to PSIM. Chapter 2 shows the fundamentals of circuit simulation with PSIM. Chapter 3 introduces the SimviewTM. Simview is PSIM’s waveform display and post-processing program. Chapter 4 introduces the most commonly used components of PSIM. Chapter 5 shows how PSIM can be used for analysis of power electronics circuits. 45 examples are studied in this chapter. Chapter 6 shows how you can simulate motors and mechanical loads in PSIM. Chapter 7 introduces the SimCouplerTM. Simcoupler fuses PSIM with Simulink® by providing an interface for co-simulation. Chapter 8 introduces the SmartCtrl®. SmartCtrl is a controller design software specifically geared towards power electronics applications. https://powersimtech.com/2021/10/01/book-release-power-electronics-circuit-analysis-with-psim/
Explore the latest power electronics principles, practices, and applications This electrical engineering guide offers comprehensive coverage of design, modeling, simulation, and control for power electronics. The book describes real-world applications for the technology and features case studies worked out in both MATLAB and Simulink. Presented in an accessible style, Power Electronics Step-by-Step: Design, Modeling, Simulation, and Control focuses on the latest technologies, such as DC-based systems, and emphasizes the averaging technique for both simulation and modeling. You will get photos, diagrams, flowcharts, graphs, equations, and tables that illustrate each topic. Circuit components Non-isolated DC/DC conversion Power analysis DC to single-phase AC conversion Single-phase AC to DC conversion Galvanic isolated DC/DC conversion Power conversion for three-phase AC Bidirectional power conversion Averaging model for simulation Dynamic modeling of DC/DC converters Regulation of voltage and current
This is the definitive reference for anyone involved in pulsewidth modulated DC-to-DC power conversion Pulsewidth Modulated DC-to-DC Power Conversion: Circuits, Dynamics, and Control Designs provides engineers, researchers, and students in the power electronics field with comprehensive and complete guidance to understanding pulsewidth modulated (PWM) DC-to-DC power converters. Presented in three parts, the book addresses the circuitry and operation of PWM DC-to-DC converters and their dynamic characteristics, along with in-depth discussions of control design of PWM DC-to-DC converters. Topics include: Basics of DC-to-DC power conversion DC-to-DC converter circuits Dynamic modeling Power stage dynamics Closed-loop performance Voltage mode control and feedback design Current mode control and compensation design Sampling effects of current mode control Featuring fully tested problems and simulation examples as well as downloadable lecture slides and ready-to-run PSpice programs, Pulsewidth Modulated DC-to-DC Power Conversion is an ideal reference book for professional engineers as well as graduate and undergraduate students.
