Aerodynamic Characteristics of an All-body Hypersonic Aircraft Configuration at Mach Numbers from 0.65 to 10.6
Aerodynamic Characteristics of an All-body Hypersonic Aircraft Configuration at Mach Numbers from 0.65 to 10.6

Author: Walter P. Nelms

Publisher:

Published: 1971

Total Pages: 108

ISBN-13:

DOWNLOAD EBOOK

Aerodynamic characteristics of a model designed to represent an all body, hypersonic cruise aircraft are presented for Mach numbers from 0.65 to 10.6. The configuration had a delta planform with an elliptic cone forebody and an afterbody of elliptic cross section. Detailed effects of varying angle of attack (-2 to 15 deg), angle of sideslip (-2 to 8 deg), Mach number, and configuration buildup were considered. In addition, the effectiveness of horizontal tail, vertical tail, and canard stabilizing and control surfaces was investigated. The results indicate that all configurations were longitudinally stable near maximum lift drag ratio. The configurations with vertical tails were directionally stable at all angles of attack. Trim penalties were small at hypersonic speeds for a center of gravity location representative of the airplane, but because of the large rearward travel of the aerodynamic center, trim penalties were severe at transonic Mach numbers.

Supersonic Aerodynamic Characteristics of a Low-Drag Aircraft Configuration Having an Arrow Wing of Aspect Ratio 1.86 and a Body of Fineness Ratio 20
Supersonic Aerodynamic Characteristics of a Low-Drag Aircraft Configuration Having an Arrow Wing of Aspect Ratio 1.86 and a Body of Fineness Ratio 20

Author:

Publisher:

Published: 1960

Total Pages: 80

ISBN-13:

DOWNLOAD EBOOK

A free-flight rocket-propelled-model investigation was conducted at Mach numbers of 1.2 to 1.9 to determine the longitudinal and lateral aero-dynamic characteristics of a low-drag aircraft configuration. The model consisted of an aspect-ratio -1.86 arrow wing with 67.5 deg. leading-edge sweep and NACA 65A004 airfoil section and a triangular vertical tail with 60 deg. sweep and NACA 65A003 section in combination with a body of fineness ratio 20. Aerodynamic data in pitch, yaw, and roll were obtained from transient motions induced by small pulse rockets firing at intervals in the pitch and yaw directions. From the results of this brief aerodynamic investigation, it is observed that very slender body shapes can provide increased volumetric capacity with little or no increase in zero-lift drag and that body fineness ratios of the order of 20 should be considered in the design of long-range supersonic aircraft. The zero-lift drag and the drag-due-to-lift parameter of the test configuration varied linearly with Mach number. The maximum lift-drag ratio was 7.0 at a Mach number of 1.25 and decreased slightly to a value of 6.6 at a Mach number of 1.81. The optimum lift coefficient, normal-force-curve slope, lateral-force-curve slope, static stability in pitch and yaw, time to damp to one-half amplitude in pitch and yaw, the sum of the rotary damping derivatives in pitch and also in yaw, and the static rolling derivatives all decreased with an increase in Mach number. Values of certain rolling derivatives were obtained by application of the least-squares method to the differential equation of rolling motion. A comparison of the experimental and calculated total rolling-moment-coefficient variation during transient oscillations of the model indicated good agreement when the damping-in-roll contribution was included with the static rolling-moment terms.

Aerodynamic Characteristics of Several Hypersonic Boost-glide-type Configurations at Mach Numbers from 2.30 to 4.63
Aerodynamic Characteristics of Several Hypersonic Boost-glide-type Configurations at Mach Numbers from 2.30 to 4.63

Author: Ernald B. Graves

Publisher:

Published: 1968

Total Pages: 29

ISBN-13:

DOWNLOAD EBOOK

An investigation has been conducted at Mach numbers from 2.30 to 4.63 to determine the static aerodynamic characteristics of several configurations designed for flight at hypersonic Mach numbers. Two all-wing and three wing-body configurations were tested through an angle-of-attack range from about -4° to 33° and an angle-of-sideslip range from about -4° to 8° at a Reynolds number of 3 x 106 per foot (9.84 x 106 meter). The results of the investigation indicated that the wing-body configurations produced higher values of maximum lift-drag ratio than those produced by the all-wing models. The high-body configurations tend to have a self-trimming capability as opposed to that for the low wing-body configurations. Each of the configurations produced a positive dihedral effect that increased with increasing angle of attack and decreased with increasing Mach number. The high wing-body models produced decreasing values of directional stability with increase in angle of attack, whereas the low wing-body models provided increasing values of directional stability with increase in angle of attack.

Hypersonic Aerodynamic Characteristics of an All-body Research Aircraft Configuration
Hypersonic Aerodynamic Characteristics of an All-body Research Aircraft Configuration

Author: Louis E. Clark

Publisher:

Published: 1973

Total Pages: 52

ISBN-13:

DOWNLOAD EBOOK

An experimental investigation was conducted at Mach 6 to determine the hypersonic aerodynamic characteristics of an all-body, delta-planform, hypersonic research aircraft (HYFAC configuration). The aerodynamic characteristics were obtained at Reynolds numbers based on model length of 2.84 million and 10.5 million and over an angle-of-attack range from minus 4 deg to 20 deg. The experimental results show that the HYFAC configuration is longitudinally stable and can be trimmed over the range of test conditions. The configuration had a small degree of directional stability over the angle-of-attack range and positive effective dihedral at angles of attack greater than 2 deg. Addition of canards caused a decrease in longitudinal stability and an increase in directional stability. Oil-flow studies revealed extensive areas of separated and vortex flow on the fuselage lee surface. A limited comparison of wind-tunnel data with several hypersonic approximations indicated that, except for the directional stability, the tangent-cone method gave adequate agreement at control settings between 5 deg and minus 5 deg and positive lift coefficient. A limited comparison indicated that the HYFAC configuration had greater longitudinal stability than an elliptical-cross-section configuration, but a lower maximum lift-drag ratio.

Aerodynamic Performance and Static Stability at Mach Number 3.3 of an Aircraft Configuration Employing Three Triangular Wing Panels and a Body Equal Length
Aerodynamic Performance and Static Stability at Mach Number 3.3 of an Aircraft Configuration Employing Three Triangular Wing Panels and a Body Equal Length

Author: Carlton S. James

Publisher:

Published: 1960

Total Pages: 42

ISBN-13:

DOWNLOAD EBOOK

An aircraft configuration, previously conceived as a means to achieve favorable aerodynamic stability characteristics., high lift-drag ratio, and low heating rates at high supersonic speeds., was modified in an attempt to increase further the lift-drag ratio without adversely affecting the other desirable characteristics. The original configuration consisted of three identical triangular wing panels symmetrically disposed about an ogive-cylinder body equal in length to the root chord of the panels. This configuration was modified by altering the angular disposition of the wing panels, by reducing the area of the panel forming the vertical fin, and by reshaping the body to produce interference lift. Six-component force and moment tests of the modified configuration at combined angles of attack and sideslip were made at a Mach number of 3.3 and a Reynolds number of 5.46 million. A maximum lift-drag ratio of 6.65 (excluding base drag) was measured at a lift coefficient of 0.100 and an angle of attack of 3.60. The lift-drag ratio remained greater than 3 up to lift coefficient of 0.35. Performance estimates, which predicted a maximum lift-drag ratio for the modified configuration 27 percent greater than that of the original configuration, agreed well with experiment. The modified configuration exhibited favorable static stability characteristics within the test range. Longitudinal and directional centers of pressure were slightly aft of the respective centroids of projected plan-form and side area.